Category Archives: POTA

Combined SOTA / POTA Activations

Posted on by — No Comments ↓

Joyce/K0JJW and I have been doing combined Summits On The Air (SOTA) and Parks On The Air (POTA) activations. Most of the SOTA summits we activate are inside parks as defined by POTA. Our primary focus is using VHF/UHF from SOTA summits with POTA is being a nice addition. Although the two programs have a lot of similarities, there are some significant differences that need to be understood.

SOTA / POTA Differences

Let’s compare the two programs to understand the differences, so you can have a successful activation with both. We will focus on differences when doing an activation so this is not an exhaustive list.

  • Summits Vs Parks. Well, this is the fundamental difference. Summits tend to be small in area, defined by a specific lat/lon coordinate and the surrounding activation zone (AZ). The activation zone is roughly defined as the area surrounding the actual summit, staying within 25 vertical meters. Parks can be almost any size and may cover many square miles. Both SOTA and POTA maintain lists of official summits or parks, so it should be clear whether one of these is valid for an activation.
  • Accessibility. While there are drive-up and easy walk-up summits, most SOTA summits require a hike. Many of them are physically challenging. Parks often have easier, park-like access. Or you can always do a 50-mile backpack trip for a POTA activation.
  • Equipment restrictions. SOTA allows you to reach the activation zone in a vehicle but you must move away from the vehicle an unspecified distant and operate totally independent of the vehicle. On drive-up mountains, our practical application of this rule is to load up our normal SOTA gear into backpacks, hike away from the vehicle, and set up for the activation. SOTA requires the use of portable power sources but not fossil-fuel generators. This pretty much means battery power, perhaps augmented with solar panels. POTA does not have such restrictions, so if you meet the SOTA requirements you’ll be valid for both.
  • Scoring. SOTA emphasizes the accumulation of activator and chaser points, while layering in other challenges such as Summit-to-Summit (S2S) scores. Each summit has a point value assigned to it, based on elevation. In POTA, all parks are created equal and the main focus tends to be on the number of activations and the number of parks hunted (chased).  POTA also has awards for the number QSOs. For example, the Kilo Award is achieved by making 1000 QSOs from a single park (usually over multiple activations). Both programs have quite a bit of variety and flexibility built into their awards and operating objectives, which is one of the reasons people enjoy the programs.
  • Successful Activation. SOTA requires only one radio contact for a successful activation. But to receive point credit for the summit, which is what most people are after, you need to make at least 4 contacts. So most SOTA activators define success as getting at least four contacts. The 4 SOTA contacts must be with 4 different stations, with no credit for working the same station on multiple bands. In contrast, POTA requires 10 QSOs for a successful activation.  POTA does count QSOs with the same station on different bands. For example, an activator could obtain the required 10 POTA QSOs by working just two stations on 5 different bands.
  • Same Location QSOs. A SOTA activator does not get credit for working another station on the same summit. That is, the other station must be outside of the summit activation zone to be counted. POTA allows an activator to work another activator in the same park for QSO credit. In fact, the activators can receive park-to-park credit for such a radio contact.

VHF SOTA and POTA

Racking up lots of contacts on VHF/UHF from a summit can be a challenge, dependent mostly on the range of your gear and the ham population in the area. Most of the time, we can get four contacts without too much trouble but at times even that can be a challenge. Getting ten contacts for POTA raises the bar higher.

Bob/K0NR displays the SOTA and POTA flags on Mt Herman (W0C/FR-063) in Pike National Forest (K-4404).

We noted that most of the hams we work on 2m FM are also workable on 70 cm FM. So an easy thing to do is to ask 2m chasers (hunters) to switch over to 70 cm and work us there, doubling the number of POTA-valid QSOs. Interestingly, the SOTA QSO count recorded in the database includes these QSOs. (But you must have contacted at least four unique stations to get the summit points.)

Because Joyce and I usually activate together, we can also work each other for POTA credit. I have discovered that many POTA activator teams make it a standard practice to pull out a couple of handheld radios and work each other on 2m FM when they first set up. OK, maybe that’s not the most exciting QSO of the day, but it is allowed.  With a dual-band HT, you can make two QSOs this way. And it is a good idea to put out a call on 2m FM to work any locals that might be hunting parks. On a summit, these QSOs would not be valid for SOTA, unless one of the operators leaves the activation zone. Yes, we’ve done that, too, taking turns hiking down out of the AZ to make a quick contact.

Summary

This covers some of the things we’ve learned about doing combined SOTA and POTA activations. Again, this is with an emphasis on VHF/UHF operating. You should study the SOTA and POTA rules carefully because this article does not cover everything. However, some of the issues I’ve outlined here are not obvious from the SOTA and POTA rules, so I hope you find this article helpful.

73 Bob K0NR

How Far on VHF SOTA?

Posted on by — No Comments ↓

Adam/K6ARK recently posted this video of his 2m SOTA activation in California. Adam does a really nice job with his videos and this one is no exception. During this activation, he worked KE9AJ in Arizona at 256 miles. This was an FM QSO, with KE9AJ running 6 watts and K6ARK running over 120 watts.

In the video, he shows the 8-element 2m Yagi antenna, which has a clever folding boom design (homebrew, I assume). You’ll notice that he is carrying quite a bit of gear in his pack, including a 160w amplifier, a Yaesu FT-857, several batteries, the Yagi antenna, and antenna masts. Adam has posted other videos of VHF SOTA activity, so check out his YouTube channel for them.

Note that at 256 miles, this is definitely propagation beyond line of sight. We’ve talked about this before: The Myth of VHF Line-Of-Sight.

This has me thinking about some of my best VHF SOTA activations, which I will list here.

Sneffels to Pikes

In 2012, for the Colorado 14er Event, Joyce/K0JJW and I climbed Mt Sneffels (W0C/UR-001) at 14,150 feet in elevation. I worked Stu/W0STU on Pikes Peak (W0C/FR-004). We both were running 5 watts on 2m FM, with 3-element Arrow II antennas. I had an FT-817, while Stu used an HT. We made the QSO without too much difficulty, at a distance of 160 miles. Stu put together this video that shows the action on both summits.

 

Capulin Mountain

Capulin Mountain (W5N/SG-009) is out in the middle of nowhere New Mexico, a long distance from populated areas. My goal was to activate it (and get the points) on VHF, but I knew it would be a challenge. I put the word out to the weak-signal VHF community and used my FT-817 (5 watts) and 3-element Yagi to make contacts. My best DX was with Arne/N7KA at 184 miles. I could hear him fine on SSB but he could not copy me, so we switched to CW to complete the QSO. Arne used a 2M12 Yagi antenna with 700 watts of power vs my 5 watts.

This turned out to be a good lesson in what happens when the two stations are imbalanced with respect to RF power. My 5 watts vs his 700 watts is a difference of 21 dB. No wonder I could hear him just fine but he was struggling to copy me. Flipping over to CW narrows the receiver bandwidth, improving the signal-to-noise ratio, and was enough improvement to make the QSO.

Capulin Mountain (W5N/SG-009) VHF SOTA

Mount Scott

Mount Scott (W5O/WI-002) is a drive-up summit (elevation 2464 feet) in the Witchita Mountains of Oklahoma. It sticks up high enough to have a good radio horizon in all directions. We stopped there to do an activation in March 2018, using the Yaesu FT-90 (set for 30 to 50 watts) and the 3-element Yagi antenna.

We easily worked a bunch of stations on 146.52 MHz FM, including K5RTN in Brownfield, TX. Later, I checked the distance to Brownfield and found that it was 245 miles, which is still my best SOTA DX on 2m FM. There was probably some favorable propagation that morning, perhaps some ducting, for this to occur. K5RTN was operating from home and I am not sure about his power and antenna.

Threemile Mountain

During the 2021 January VHF Contest, we decided to activate Threemile Mountain (W0C/SP-107), which is usually accessible, even in the winter months. Because it is in the Pike National Forest (K-4404), I did a combo operation of SOTA, POTA, and VHF contest. At 10,020 feet in elevation, it is not the highest summit in the region but it has a good radio horizon in all directions.

Also, the hike is relatively short, so I packed the Yaesu FT-991 and a 20 Ah battery, which gave me more power (50 watts) on 2m and 70 cm. Not only that, I actually fired it up below 50 MHz and made some HF contacts, using single-band end-fed halfwave antennas.

I was working a few stations in Denver on 2m SSB when I heard Larry/N0LL calling me from Smith Center, KS. Larry is a well-known Big Gun on VHF with excellent antennas. I’ve worked him in past contests on various bands and modes but I was surprised how strong he was coming in at Threemile Mountain. We probably had favorable conditions on 2 meters that day but nothing exotic, to make a 372 mile QSO. I’ve worked longer distances on 2 meters but this is my best DX for SOTA.

Radio Fun on Threemile Mountain (W0C/SP-107)

Power and Antenna

Most ham transceivers have decent receivers, so the choice of radio on the receive side is not that critical. (OK, you can add a preamp in front of the receiver to improve it.) The big difference for making QSOs (or not) on 2 meters is antenna and power level.

Improving your antenna is normally the first step in improving your VHF SOTA station, because it helps on both transmit and receive. Joyce/K0JJW and I almost always use the 3-element handheld Yagi from Arrow Antenna. Arrow does not specify the gain, but various sources have measured it at 6 dBd. We have made many QSOs over the years where the extra 6 dB made the difference. An omnidirectional antenna would have come up short. I’ve been looking for a higher gain antenna to use for SOTA but have not found one that I like. Adam’s 8-element antenna is tempting but longer antennas pretty much require a mast, which adds weight to the pack. One of the benefits of the 3-element Arrow is that it is handheld, so we don’t carry a mast. Of course, having two of us activating together really helps…one person can hold the antenna while the other operates and logs. A handheld antenna with a single operator can be a challenge.

Concerning power level, the Capulin QSO with N7KA illustrates what happens when two stations are imbalanced with respect to RF power. After this experience, I did purchase a small 2m amplifier that boosts the 5 watts from the FT-817 to 35 watts. It is compact and not too much of a DC power hog.  I think we also heard an imbalance with the QSO between K6ARK and KE9AJ. KE9AJ’s signal was a bit noisy at K6ARK while K6ARK’s signal was full quieting 59 at the other end. This is not a surprise with K6ARK at around 120 watts and K6ARK at 6 watts (13 dB difference).

For higher power on 2 meters, you generally need to bring a bigger radio or an amplifier. The popular HT is generally limited to about 5 watts. For 2m FM, we’ve been carrying the Yaesu FT-90, which is a pretty compact radio and can put out 50 watts of RF power (FM only). On the Threemile Mountain activation mentioned above, we took the FT-991, which is not very SOTA friendly, but it also does 50 watts on 2 meters…and all modes.

Battery capacity also comes into play as higher power requires more DC current. The FT-90 manual says it draws 9.5 amps at full 50 watts of power on 2 meters. (We usually run it at lower power but will punch it up to 50 watts when required.) The FT-991 manual says it draws 15 amps when transmitting at full power on 2m or 70cm. My 160 watt 2m (Mirage) amplifier can draw up to 30 amps on transmit. Wowzy, that’s some real current! The point is that as you increase power, you need to look at your battery situation more carefully.

It might sound like I am suggesting that we should maintain a power balance between the two stations. That’s not the case and is often not even practical. When one station is much stronger than the other, it can be used to advantage. The stronger station is easily heard and the weaker station can point the antenna in the right direction to peak up the signal. The weaker station consistently hears the stronger station, so now the challenge becomes to just get a few seconds of successful transmission in the opposite direction. You keep trying until the weaker station manages to get through. Compare this to having two lower power stations trying to make a contact. They may not even hear each other at all because the antennas are not pointed optimally. When they do hear each other, they are both struggling to hear the other station and complete the QSO. This lowers the probability of completing the contact.

So how much power should you run on 2 meters for SOTA? Of course, More Is Better, except for the extra weight in your backpack. The difficulty of the hike comes into play…on shorter hikes, weight does not matter so much. I am finding that 5 watts is on the skimpy side. On the other hand, going much above 50 watts requires larger batteries, so I am thinking the sweet spot is around 30 to 50 watts. If I do happen to work a base station running 1kW, my signal will be 13 dB lower with 50 watts (worst-case scenario). This is just my opinion, your mileage may vary.

Summary

So can we all agree then that VHF signals can go beyond line-of-sight? These examples are basic tropospheric paths and do not include the exotic propagation modes such as meteor scatter, sporadic-e, aurora, EME, etc. I’ve used most of those modes to work longer distances but not during a SOTA activation. Most hams know that SSB and CW are more effective than FM when signals are weak. In fact, FM weak-signal performance is lousy. Still, we see multiple examples of making some long-distance contacts with FM.

73 Bob K0NR

Tips and Tools for Managing Logs

Posted on by — 7 Comments ↓

Lately, the majority of my radio activity has been SOTA and POTA activations, sometimes simultaneously. The logging requirements for the two programs are different so I often need to adjust the log file before submitting it. Even more common, I need to double-check and fix errors in my SOTA and POTA logs. Some of this comes from the idiosyncrasies of the logging software but often the errors are introduced by the operator. (That would be me.)

The SOTA CSV Log Editor

Here are a few tools and tips to assist with your portable logging.

SOTA and POTA Logging Tools

For SOTA, Joyce/K0JJW and I normally just use a paper log. If the number of QSOs is small, the paper method is easy and reliable. Later, I use the SOTA CSV Log Editor by G0LGS to enter the information into a CSV (Comma Separated Variable) file. This program is reliable and easy to use. This Windows program uses CSV for the log files but it can also export the log in ADIF (Amateur Data Interchange Format).

For POTA activations, we tend to have a larger number of QSOs so I try to log them in real-time on a computing device. The HAMRS logger is a relatively new logging program by Jarrett/KB0ICT. It runs on multiple platforms, including Windows, Linux, Mac, iOS and Android. I’ve been using it on Windows, an iPad, and my iPhone. The user interface is tuned for portable operating with just enough features and not a lot of fluff. There are some bugs here and there but Jarrett continues to release bug fixes and new features at a steady rate. I have not encountered any serious issues and I really like the implementation. HAMRS exports files in ADIF format.

CSV Files

A CSV file just has the variables of interest separated by commas, usually one QSO on each line. These files are a bit cryptic but can be read by humans with just a little effort. Below is a CSV file generated for a SOTA activation. Note that the first line contains the header information that defines the variables in the subsequent lines.

An example of a CSV file from a SOTA activation.

Sometimes it is very helpful to just be able to edit a CSV file directly. For example, if Joyce/K0JJW and I worked the same set of chasers from a summit, I can create a new log file by doing a find/replace of my callsign with her callsign. For this, I use a simple text editor such as Windows Notepad. Its native file format is plain text so it won’t inadvertently add in additional formatting or characters. Excel (or another spreadsheet) will handle this format but make sure you output a clean CSV file.

ADIF Files

ADIF is the most flexible and portable file format for ham radio logging. It can be uploaded to Logbook of The World and imported into most comprehensive logging programs. ADIF files are a bit more complex, using Data Types, Enumerations, and Fields to produce a flexible file format that is also human-readable.

ADIF file from SOTA CSV Log Editor,  for a SOTA activation.

Again, a simple text editor (Notepad) is useful for making edits to an ADIF file. The particular file shown above was exported from the SOTA CSV Editor with each field on its own line. This makes each QSO easier to read but the file has a lot more lines in it.

The program ADIF Master is very good at viewing ADIF files and making changes to them. I often use it to do a final check of the log before submitting it.

ADIF Master is very useful for viewing ADIF files from SOTA, POTA or other events.

When ADIF Master saves an ADIF file, it puts each QSO on one line. The fields and variables remain the same, but the spacing changes. This reduces the overall length of the file (number of lines) but it can be more difficult to read.

ADIF Master flattens the ADIF file by putting one QSO on a line.

Sometimes you might need to convert between CSV and ADIF file formats. There are online tools to do this but I have not used them enough to comment.

I am not going to try to explain the various fields and labels used in these file formats. For the ADIF format, take a look at the detailed specification here: https://adif.org/. A few times, I have needed to find a specific field that was missing and add it to an ADIF file. ADIF Master can do this for you, but you must know the exact name of the field.

These are a few things I’ve learned along the way playing around with SOTA and POTA logs. I hope this is helpful.

73 Bob K0NR

Yellowstone and Grand Teton: SOTA and POTA

Posted on by — No Comments ↓

Visiting Yellowstone and Grand Teton National Parks is a favorite trip for us. It is a 9-hour drive to get there from Colorado, so we can make it in a day.  In September, we visited these two parks with a blend of activities in mind: RV camping, hiking, viewing wildlife and ham radio. The ham radio part means Summits On The Air (SOTA) and Parks On The Air (POTA).

The Teton mountains tower above the Snake River.

Our trip started from Monument, CO, followed by a stop at our cabin near Trout Creek Pass. Heading north, we spent one night at Steamboat Lake State Park (Colorado), which broke up the road trip into smaller sections.

A few of the many buffalo (bison) in Yellowstone National Park.

Grand Teton NP

Grand Teton NP listed 27 activations for POTA (POTA K-0031) which is really not that many activations for such a well-known national park. The park and the surrounding national forests have many SOTA summits available, some quite difficult to climb (such as 13,770 foot Grand Teton).   We camped two nights at Colter Bay RV Park, inside the park. This is a decent RV-style campground with full hookups and campsites packed in a bit tight.

Joyce/K0JJW campsite operating POTA from the Grand Teton campsite.

Our usual POTA station is the Yaesu FT-991 driving a single-band end-fed halfwave (usually 40m, 20m or 17m) supported by a fishing pole and powered by a 20 Ah Bioenno battery. Joyce/K0JJW likes to use a paper log but I usually log my contacts with HAMRS, either on my notebook PC or an iPad. HAMRS is a relatively new logging program that runs on most operating systems (Windows, Mac, Linux, iOS, Android, etc.) It is tuned for portable operating, with templates for SOTA and POTA. Check it out, if you haven’t tried it.

One unfortunate surprise while operating from the campsite was a ton of RFI coming from the electronic devices in use by the herd of RVs. The noise floor on 20m was S5— not so good.  It seems that today’s RV enthusiast brings along complete wireless network support with internet access points, WiFi routers, and their associated Part 15 emissions. Oh, well.

After setting up on 20m SSB, K0JJW and I both completed 10 QSOs with some difficulty. We were clearly being heard but we had trouble digging signals out of the noise.

Next up was a VHF SOTA activation on Signal Mountain (W7Y/TT-161). This is an easy-to-access drive-up summit with a great view, highly recommended with or without a SOTA activation. We debated on whether to use HF for SOTA on this trip. Normally, we’ve stuck to VHF/UHF on SOTA summits, as part of the Height-Above-Average-Terrain experience. However, knowing that Northwest Wyoming is a bit sparse for VHF activity, we could easily get skunked on a SOTA activation (less than 4 QSOs). Despite that, we opted to stick with VHF for SOTA and focus on a successful activation (1 QSO or more), with or without the SOTA points. On Signal Mountain, we worked two stations on 2m FM, including Steven/KB7ITU in Rexburg, ID, about 60 miles away. (Hey, we worked another state on VHF!)

Speaking of VHF, we used our dualband mobile (IC-2730A) to listen to the national park repeaters while we travelled through the park. Our dual-receive radio always has 146.52 MHz on one side and “something else” on the other side. When inside large national parks, we’ll set the second receiver to a national park frequency. These are generally conventional FM in the 162 to 173 MHz range. I won’t list the Teton and Yellowstone frequencies here but you can find them with a little searching on the interwebz. For example, see wiki.radioreference.com for Yellowstone NP frequencies.

Yellowstone National Park

Yellowstone ( POTA K-0070 ) had only 22 POTA activations, not that many considering it is the nation’s first national park. It also has quite a number of SOTA summits of varying difficulty.

We camped two nights at Grant Village campground, a basic national park campground. The campground had no hookups but the campsites are well spaced with many trees and flush toilets. (The only problem we had was when the park service booked another group of campers onto our campsite one night.)

Joyce and our RV (Rocky Victoria) at the Grant Village campsite.

During a previous visit to Yellowstone, we activated Lake Butte (W7Y/PA-219). On this trip, we had our eye on Mount Washburn (W7Y/PA-163), a well-known 10k summit and popular hike, but the road that provides access to it was closed for the summer due to construction. (OK, maybe next time.)

Bob/K0NR operates 2m FM from the unnamed summit W7Y/TT-139.

Instead, we decided to try an unnamed summit 8770 (W7Y/TT-139) that was relatively easy to access but had not been activated for SOTA. We found some trip reports that said there is a nice trail to the summit and the only complaint was that the summit does not have a view due to the many trees.  We parked at the Divide Trailhead, about 12 miles west of Grant Village. The trail is 1.8 miles in length (one way) with 700 feet of elevation gain. So not too difficult but a real hike.  The summit is broad and sure enough with lots of trees, so no view. Practice normal bear precautions on this trail.

Practice standard bear precautions in this area.

Again, we opted for VHF SOTA, knowing that we might not get enough radio contacts for points…but we only needed one contact to qualify as the first activation. We worked two mobile stations passing through the park on 146.52 MHz. Yes, it is good to always be monitoring the calling frequency. You never know who is going to show up.

For POTA, we noted that the Continental Divide Trail National Scenic Trail (K-4558) passes through Yellowstone NP, which would allow for a double activation.  The CDT has always been special to me as it passes through Colorado and provides some of the most scenic hiking in the state. It only had 15 activations listed at that time, two of those were ours from when we activated it a month earlier, in Colorado. We choose the Old Faithful area as a good place to activate Yellowstone NP ( K-0070) and the CDT. We set up near the edge of the parking lot, away from the crowds. Again it was the FT-991 driving the endfed halfwave on 20m SSB. It was midday, so we expected good 20m propagation (and a nice pileup for Yellowstone) but the band was not cooperating. We both made at least 10 QSOs for a successful activation, so we count that as a win, but the pileup never happened.

Besides the radio operating, we had a good time touring through the park and looking for wildlife. We saw tons of buffalo, not quite so many elk and deer, but no bears or wolves. We have had better wildlife viewing on previous trips but it was still fun.

Heading South

Then it was time to start home, heading south out of Yellowstone back through Grand Teton. Of course, we were monitoring 146.52 MHz, when we heard Lorene/KG6MWQ  on unnamed summit 7586 (W7Y/TT-164). She was on the summit with AE6NH, operating both HF and VHF. It was great to catch a VHF activator in Yellowstone. This was the first activation for TT-164, so congratulations to both of them.

Two POTA activators smiling for the camera (Joyce/K0JJW, Bob/K0NR).

We decided to make a stop at the Colter Village area on the way through Grand Teton NP. Our first priority was to use the shower facilities there. Our second priority was doing another POTA activation.

Yaesu FT-991 set up on small camp table, with microphone and two sets of headphones.

This time we set up in a large parking lot, away from anything that might produce RFI. Again, it was 20m SSB using the halfwave antenna supported by a fishing pole. We sat near the RV on our camp chairs and table. Our typical configuration is to have two sets of headphones so both of us can copy well. We just use the standard handheld microphone which is easily passed between us when we change operators.

Typical antenna setup with fishing pole inserted into a plastic pipe attached to the RV ladder. A wire antenna is hung from the end of the pole.

Later in the day, we exited the park and headed south through Jackson, WY. We stayed overnight at a farm near Afton, WY which is surrounded by Bridger-Teton National Forest (K-4535). Of course, we needed to do one more POTA activation. We searched around for a usable spot to park and then fired up on 20m SSB. Propagation was OK but not great but we got it done.

The next day, we were up and going early, driving the rest of the way home to Monument. It was a wonderful road trip that blended sightseeing, hiking, camping, and ham radio. Let’s go do it again!

73 Bob K0NR

My POTA Activation Guidelines

Posted on by — 2 Comments ↓

Joyce/K0JJW and I have been doing Parks On The Air (POTA), in addition to our normal Summits On The Air (SOTA) activations. Sometimes we do both simultaneously.  (See More on SOTA and POTA.) SOTA will probably continue to be our top priority because, well, you just can’t beat operating from the summit of a mountain.

Bob/K0NR doing a SOTA plus POTA activation on Threemile Mountain (W0C/SP-107) and Pike National Forest (K-4404).

SOTA and POTA

The programs have a lot in common but still have some significant differences. One of the key differences is that SOTA inherently puts you outdoors and away from your vehicle. This happens naturally if you hike some distance to get to a summit. But even on a drive-up mountain, the rules (W0C ARM) say:

Operations must not be in, or in the close vicinity of a motor vehicle, cannot use a permanent electrical power source, nor use a fossil fuel generator in any fashion. No part of the station may be connected in any way with the motor vehicle. All equipment must be operated from portable power source (batteries, solar cells, etc).

I have come to appreciate the wisdom of these restrictions as it helps keep the program “backpack portable,” without being overly restrictive. POTA does not have these restrictions, so it is common to see POTA activators operating from inside vehicles, inside RVs, even inside buildings using commercial power. Quite different from SOTA and I suppose that’s just fine. It does provide a higher degree of flexibility and radio hams can choose to participate in a manner that works for them. Certainly, this is a good thing for physically challenged individuals.

Joyce/K0JJW operating from a park picnic table, using the FT-991 and a Bioenno battery pack.

Here is a definition of “park” as it applies to national, state and local parks.

Park (noun):
an area of land, usually in a largely natural state, for the enjoyment of the public, having facilities for rest and recreation, often owned, set apart, and managed by a city, state, or nation.

The main idea of visiting a park is for people to enjoy being outdoors in a natural setting.

My POTA Rules Guidelines

Everyone gets to decide “how to POTA” as long as they stay inside the POTA rules.  We’ve adopted these guidelines to keep POTA oriented towards outdoor, portable radio operating.

  1. Set up outdoors Get outside the vehicle and find a place to set up outdoors. At a picnic area or campsite, this might be using a picnic table or it might be setting up on a stump, on a rock, or on the ground. Whatever works. Even a tailgate-style operation is better than just sitting in the car.
  2. Take a hike Before or after the activation, take a hike. Get some exercise and explore the park. A mile or two of walking in the forest is usually a good thing.
  3. See the park Some parks are not very hikeable, but you can still explore what is special about the place. Look around to see what is interesting about the park and why it exists.

Note that these are guidelines and not strict rules. This is what we try to do for a POTA activation. There will be times when this is not practical and that’s OK, too. Sometimes we’ll do a Drive-Up/Drive-By activation when time is limited or the weather is bad. For example, I recall a recent winter activation in K-4407 where the temperate was -3 deg F. We stayed in the truck for that one!

So keep on POTAing and having fun with ham radio.
These are my thoughts, what do you think?

73 Bob K0NR

Parks, Summits and Roadtripping

Posted on by — 3 Comments ↓

Getting out on the road and exploring is always fun, especially if you have ham radio on board. Joyce/K0JJW and I have been doing quite a bit of travel lately and we just completed our longest road trip so far with our RV.

Overview of the trip: Colorado to Key West, Florida and back again.

Our main destinations for the trip were four national parks: Congaree NP, Biscayne NP, Everglades NP, and Dry Tortugas NP. This determined the main route but we also found plenty of other things to do along the way. We started in Colorado, cut the corner across New Mexico into Texas, then east through Oklahoma, Arkansas, Mississippi, Alabama, Georgia and South Carolina. Then we headed south to Florida and ended up in Key West. Our return trip followed the gulf coast back to Texas, then back home.

Travel Philosopy

Planning a trip is full of trade-offs, so it is useful to have a general approach that the participants agree on. Our approach to this trip was to not drive too far every day but drive enough to hit the various places we wanted to visit. We are still working to find the right balance. This trip lasted 39 days, covering 6000 miles, which is about 150 miles per day. Some days we drove very little and other days were longer, maybe 400 miles.

Although the trip was created around the national parks, we filled in with interesting stops along the way. In particular,  we like to camp at state parks: the campgrounds are great and there’s usually something interesting about the park to enjoy. And did I mention they are natural Parks On The Air (POTA) opportunities? We also tried to work in some Summits On The Air (SOTA) activations that are relatively easy to access.

Rocky Victoria

Our recreational vehicle (RV) is a 2018 Winnebago Paseo, built on a Ford Transit chassis. We named her Rocky Victoria, using non-standard phonetics, but usually just refer to her as “Rocky”.

Rocky Victoria is our Winnebago Paseo RV.

Compared to your typical car or SUV, this Class B RV is huge. Compared to other RVs, this vehicle is small, about 22 feet long, usually fits in a standard parking space. With all of the normal RV stuff installed (stove, microwave, sink, refrigerator, toilet/shower combo, bed, etc.) there is not a lot of room left for personal gear.

Rocky fits us really well because it is easy to drive, getting in and out of places without much hassle. Also, setup and tear-down time at a campsite is minimal. One limitation is poor ground clearance, which is fine for forest service roads in good condition but not appropriate for offroad use. This affects what SOTA and POTA activations we do.

Radio Gear

We have an ICOM IC-2730A in Rocky, for normal 2m/70cm FM comms while running down the road. The antenna (not visible in the photo) is just a short whip on the driver’s side of the hood.

Rocky is not a big RV so by the time we load up all of our stuff, it is full. So the radio gear (and everything else we take along) must follow the backpacker principle of “take only what you need, use what you take.” No room for extra stuff you don’t use.

For this trip, we took along two ham stations:  A basic VHF SOTA station and a capable, picnic-table POTA station.

VHF SOTA Station

The VHF SOTA station is very compact and easy to carry. It covers the 2m and 70cm bands on FM, which is usually sufficient for us. The RF output power is only 5W, so it does not have the punch of one of our higher power radios. Not a bad tradeoff though.

Two Yaesu FT-1DR 2m/70cm handheld transceivers
Arrow 3-element Yagi 2m antenna
Two RH 770 dualband SMA antennas
HT chargers and other accessories

Picnic Table POTA Station

The POTA station is built around the FT-991, which is a 100 watt transceiver (HF/VHF/UHF) that is reasonably compact. We use a 20 Ah LFP battery to power the radio so it is portable and independent of the RV power sources.

Yaesu FT-991 Transceiver (HF, 6m, 2m, 70cm)
End-fed halfwave antennas for 40m, 20m, 17m, 15m, 10m
Roll-up j-pole antenna for 2m/70cm
20-foot fishing pole to support antennas
Two 25-foot lengths of RG-8X coaxial cable
12V, 20 Ah LFP Battery (Bioenno Power)

Joyce/K0JJW operates the picnic-table POTA station.

The POTA station does a great job at a campsite, usually on a picnic table. The POTA station fits inside my Kelty backpack so it can be taken for a hike. It is a bit heavy for a typical SOTA summit but works OK for drive-up and short-hike summits. It can also be set up inside the RV if required.

Single-band end-fed halfwave antenna (PAR EndFedz) for 20 meters.

Typically, we are going to try operating on 20m or 17m so that the halfwave antenna easily hangs from the fishing pole support. Depending on conditions, we often have to use 40m which takes a little more work to hang. Not a huge problem, though.

Collapsible fishing pole for supporting wire antennas.

For portable operating, I’ve tended to use a variety of end-fed wire antennas supported by a non-conductive pole of various sizes. For this trip, we used a 7 meter (21 feet) telescoping fishing pole that collapses to about 30 inches.  This pole will fit into my SOTA backpack.

20m halfwave antenna supported by the fishing pole mounted on the RV. (The 20m halfwave needs to be hung at an angle to be supported off the ground.)

To support the fishing pole directly from the RV, I attached a short length of plastic pipe to the ladder. It is a simple matter to slide the pole into pipe, resulting in the top of the pole being about 26 feet off the ground.

A short piece of plastic pipe is attached to the RV ladder so the fishing pole can be easily inserted.

The combination of the two stations gives us a lot of options for ham radio operating.

Summits On The Air

We activated three summits along the way: Mount Scott (W5O/WI-002) in Oklahoma, Choctaw County HP (W5M/MS-001) in Mississippi, and Monte Sano Mountain (W4A/HR-002) near Huntsville, AL.

Monte Sano Mountain is just east of Huntsville, AL inside Monte Sano State Park.

Monte Sano Mountain turned out to be a unique location because it is located in the Monte Sano State Park. The park surrounds the summit, which is broad and flat. We determined that the park campground is within the activation zone, so we camped there and did both SOTA and POTA activations.

Parks On The Air

We did a number of POTA activations along the way. This was done opportunistically, typically in the afternoon after we had set up our campsite. Our radio operating used SSB on 20m or 40m, along with a few 2m FM contacts.

K-0688  Lake Meredith National Recreation Area   US-TX
K-1090  Lake Chicot State Park   US-AR
K-1048  Monte Sano State Park  US-AL
K-0017  Congaree National Park US-SC
K-1832  Anastasia State Park  US-FL
K-0024  Everglades National Park  US-FL
K-0635  St. George State Park  US-FL
K-2992  Brazos Bend State Park  US-TX

Every one of these activations was a lot of fun. There’s nothing like sitting outdoors in the sunshine working a pileup of enthusiastic POTA hunter stations.

Summary

In this post, I emphasized the ham radio activity during this trip. Radio operating was not our main goal but it was a big part of the overall experience. Joyce and I had a fantastic time touring this section of the country, and we are looking forward to our next trip.

73 Bob K0NR

Reactions to the North America Adventure Frequency

Posted on by — 9 Comments ↓

While I did not originate the idea, I have been promoting the use of 146.58 MHz as the North America Adventure Frequency.  (Rex/KE6MT and George/Kj6VU came up with the idea.) My previous blog post explained the thinking behind it, along with my own personal biases, I’m sure.

When presented with the idea of The Other Simplex Frequency, I generally get three types of reactions:

1. Great idea! These people generally live or operate in locations where the 2m FM calling frequency (146.52 MHz) can get kind of busy, so they see that having an alternate frequency that everyone knows about has value. They may or may not still call on .52 but having another designated frequency is a plus.

2. It will never get used in my area This reaction comes from locations where people tend to congregate on 146.52 MHz and will probably not monitor any other frequency. The SOTA activators say stuff like “I’ll never contact anyone on 146.58 MHz so I’ll have to just use keep using 146.52.” This is not a problem, do whatever makes sense.  The North America Adventure Frequency will probably not get used everywhere and that is just fine.

3. What, people actually talk on 2m FM simplex? These folks are just plain missing out. I don’t know how to help them.

73 Bob K0NR

Radio Fun on Threemile Mountain (W0C/SP-107)

Posted on by — 3 Comments ↓

Lately, for the ARRL January VHF contest, I try to find a SOTA summit to activate. Operating time is usually just a few hours, so it does not make for a big score. The main advantage is for VHF SOTA (Summits On The Air) because there is a lot more activity on 2m CW and SSB. This year, I wanted to go for the mountaintop trifecta of SOTA, POTA (Parks On The Air) and VHF contest in one activation.

Threemile Mountain is an easy SOTA summit: easy to access via forest service roads and an easy hike.
Joyce/K0JJW operating the portable station on 2m FM.

Threemile Mountain (W0C/SP-107) emerged as the activation summit because it is not too far from our cabin and accessible in the winter. (This time of year, the roads to many of our favorite summits are blocked.) For POTA, it is located in the Pike National Forest (K-4404). Because it is a short hike, I concluded that I could carry the Yaesu FT-911 and the 20 Ah Bionno battery. This would cover all the bands, give us more RF punch and still have plenty of battery capacity.

The portable station with 100 watts on HF, 50 watts on 2m/70 cm.

I carried quite a collection of antennas which gave us plenty of operating choices. We started out on 2m and 70 cm FM, working mostly local stations. This quickly got us enough contacts for SOTA and POTA points. We used a rollup J-pole for 2 meters and 70 cm, until it became intermittent and the SWR went wild. Then we switched to the Arrow 3-element Yagi for 2 meters.

Bob/K0NR operating from Threemile Mountain.

About that time, I decided to see what was happening on 2m SSB. There were a number of contest stations on the air, mostly from the front range cities (Denver, Boulder, Colorado Springs, …). I worked a bunch of them using 50 watts from the FT-991 to the 2m Yagi antenna (horizontally polarized).

The QSO between K0NR on Threemile Mountain (DM78) and Larry/N0LL near Smith Center, Kansas (EM09).

Suddenly, I was surprised to hear N0LL from Kansas calling me. I’ve worked Larry before from Colorado but it usually was from a really good location such as Mt Herman or Pikes Peak. Even then, we often had to switch to CW to complete the contact. Today he was louder than many of the Denver stations. We easily worked on SSB, which turned out to be a new personal best DX for me from a SOTA summit (372 miles).

We deployed both the SOTA and POTA flags today.

After things slowed down on 2m SSB, I decided to make some HF contacts. The North American QSO Party (SSB) was active, so I decided to set up for 20m and see who I could work. Running 100 watts to an endfed halfwave kept me competitive with the contest stations. Then I moved up to 17m SSB and worked non-contest POTA and SOTA chasers.

Bob/K0NR and Joyce/K0JJW hanging out on the summit of Threemile Mountain.

We both accomplished the three-in-one mountaintop activation for SOTA, POTA, and the VHF contest. I also worked the NA QSO Party, so that makes it four-in-one, but who is counting?  The January weather cooperated with us with almost no wind on the summit, about 28 degrees F. We sat there in the sunshine and just enjoyed the view before hiking back down.

73 Bob K0NR

North America Adventure Frequency: 146.58 MHz

Posted on by — 13 Comments ↓

Recently, on the nasota group,  there was a discussion about designating an alternative 2m FM frequency for Summits On The Air (SOTA) use (instead of 146.52 MHz). The main driver for this is that 146.52 MHz can get busy with other radio traffic and/or a busy SOTA activation can tie up the calling frequency for a long time.

Rex KE6MT (SOTA W6 Association Manager) kicked it off with:

A friend of mine, George KJ6VU, has been talking with me and several others about the idea of an FM “Adventure Frequency.”  It would be for more than just SOTA – other *OTA’s could also use it. There are other ideas to layer on top of it, such as tone signaling so that you don’t have to hear traffic you don’t want to hear, and repeater infrastructure for announcing someone’s on the frequency with a given tone, etc.  But the core thing would be to decide on a frequency and really get it in use.  The National Calling Frequency (146.52) can be great for a few contacts sometimes, but other times it’s problematic either because it’s being hogged or because nobody’s listening.  Of course, this Adventure Frequency could have the same issues present themselves differently, but would alleviate some and pave the path for future additions mentioned above.

I have previously written about the challenges of using 146.52: The Use of 146.52 MHz

One important idea is to include the other “OTAs” in adopting this frequency, most notably Parks On The Air (POTA). Hence the name “Adventure Frequency,” and not “SOTA Frequency.” It is really about hams operating portable in an outdoor setting. Of course, like all amateur spectrum, this frequency must be shared with other users.

It may seem like a simple thing to choose a nationwide simplex frequency but VHF band plans are managed regionally. In particular, there is a mix of 15-kHz and 20-kHz channel spacings. (For more background on this see Simplex Channel Confusion on 2 Meters.)

After some discussion, the group settled on 146.58 MHz. There was some dialog around using CTCSS for signaling but nothing specific surfaced.

Some key points:

  • The NAAF is 146.58 MHz.
  • This frequency is in addition to, not a replacement for, the National Simplex Calling Frequency 146.52 MHz.
  • Local usage will likely vary depending on needs.
  • Program 146.58 MHz as The Other Simplex Frequency in your radio.

What does this mean to you?

Program 146.58 MHz into your radio and have it available. If you are doing SOTA (or POTA) activations, consider using this frequency, especially if you are in an area where 146.52 is used a lot. (I’ve already started using this frequency for SOTA activations near urban areas.)

73 Bob K0NR

POTA: Arkansas River Headwaters State Park (K-1208)

Posted on by — No Comments ↓

The Arkansas River Headwaters is a unique recreation area that follows the upper Arkansas River in Colorado, extending roughly from Leadville to Pueblo. POTA has it listed as the Arkansas River Headwaters State Park, but the Colorado Parks and Wildlife website shows it as the Arkansas Headwaters Recreation Area. This area is a bit unique, a cooperative effort involving Colorado Parks and Wildlife, the Bureau of Land Management, and the US Forest Service. See map here.

Joyce/K0JJW working the pile from POTA K-1208

Joyce/K0JJW and I decided to activate this park earlier this week, enjoying a nice sunny day. We operated from the Collegiate Peaks Overlook, which has a picnic area and an excellent view of Mount Princeton and adjacent peaks.

The wire antenna is supported by a SOTAbeams mast inserted into a drive-on mount.

For POTA, our standard station configuration is the Yaesu FT-991 transceiver driving an end-fed halfwave antenna, usually on 20m or 15m. We have a collection of end-fed halfwave antennas that cover 40m and up.  We have bigger and smaller transceivers available to us, but the FT-991 is small enough to be portable but includes an antenna tuner and has 100 watts of output available. (Typically, we run about 50 watts of RF output on battery power.) Our power source is a Bioenno 12V 20aH LFP battery.  This battery is lightweight and compact, capable of running the FT-991 for hours.

Bob working VE4RBH and AG7KO on 20 meters.

We set up our station on a convenient picnic table. We had hoped to lash the mast to a conveniently-located post or tree, but none were present. Our backup plan was the drive-on mount, held by the front tire of the truck. The 20m band was alive so we just set up on that band and never looked back. We also worked some of the locals on 2m FM. It is always fun to see who shows up on that band.

Here’s Joyce working AA5UY in Louisiana.

I don’t think we have really optimized our POTA setup but we have found an approach that works well. Never underestimate a properly-fed halfwave antenna up in the air.

73 Bob K0NR

More On SOTA and POTA

Posted on by — No Comments ↓

Recently, I commented on participating in the Parks On The Air (POTA) program: How About Parks On The Air? Since then Joyce/K0JJW and I have done a few POTA activations, including a few combination SOTA (Summits On The Air) + POTA activations. We are starting to sort out how SOTA and POTA work for us. I am sure this will evolve over time as there are many operating options with both programs. But here is what we’ve done so far.

Recall that we’ve been focusing on VHF/UHF operating for SOTA, although I did break down and actually made some HF contacts from a SOTA summit recently. VHF/UHF  is a good match for SOTA (Height Above Average Terrain). However, for some remote summits, it can be a challenge to get enough radio contacts (4) to qualify for the SOTA points. Using HF can be a big help in generating contacts. POTA can also be done with VHF, some parks have high elevation, but many of them are not attractive VHF locations. POTA requires 10 radio contacts to qualify for points, so that raises the bar a bit, too.

Bob/K0NR on Mount Herman, displaying the SOTA and POTA flags.

Yesterday, we decided to hike up Mt Herman (W0C/FR-063) for a short afternoon VHF/UHF activation. I posted both a SOTA alert and a POTA alert.  We made plenty of radio contacts (40 total) and submitted logs to both the SOTA and POTA websites. I know there were SOTA chasers out there but I’m not sure if anyone worked us specifically for POTA. As usual, a lot of hams give us a call just because it is fun to work someone on a summit (without any SOTA or POTA interest).

The majority of our SOTA activations in Colorado are in national forests, which count as “parks” for POTA. So it is easy to tack on a POTA activation when doing SOTA.

Vehicle-Based POTA

Joyce and I also did some POTA activations from a vehicle. It is pretty easy for us to get to Pike National Forest (K-4404) or San Isabel National Forest (K-4407) and set up a portable station.

The vehicle-based POTA station, as used in Yellowstone National Park during the year of the ARRL NPOTA program.

We used a Yaesu FT-991 and endfed halfwave antennas for 20m and 15m, supported by a SOTAbeams pole. This is the same configuration I’ve used for portable operating from many locations, including some Caribbean islands. I recently purchased a 20 Ah LFP battery from Bioenno Power to use as a power source so that we don’t rely on the vehicle battery.

We focused on HF for these POTA activations and were pleased to have decent pileups of stations calling us on the 20m and 15m bands. Fifty watts to a halfwave antenna works just fine. We also made it a point to call on 2m FM and usually picked up a handle of contacts on that band, too.

What’s Next?

At this point, our outdoorsy portable operating is looking like this:

  • SOTA Summits – if the summit is in a park, we will probably go ahead and submit a POTA log along with the SOTA log. Many of the W0C SOTA summits are in national forests, national parks or state parks. VHF-only activations will probably have less impact on POTA…those chasers/hunters tend to be on HF. On HF, we will be running QRP power levels.
  • POTA Parks (day trip) – another option is for us to just stop by one of the national forests or a state park and get on the air. (Pike National Forest is about 2 miles from our home.) This will be focused on the HF bands but we can always make a call or two on VHF. This will be operating from or close to a vehicle, so probably running 50 watts on HF with a wire antenna.
  • POTA (RV camping) – we’ve been RV camping in state parks and national forests this past year. An obvious additional activity is to set up on HF for a POTA activation. We haven’t done this yet.

I’ve already done a combination VHF Contest and SOTA activation, so this could be extended to include POTA. Three Things In One. In fact, some locations qualify for more than one POTA park, so maybe it is time for a Four-In-One.

73 Bob K0NR

How About Parks On The Air?

Posted on by — 3 Comments ↓

Recently, I gave a presentation to the ARROW radio club in Ann Arbor, MI on the topic of “Having Fun With VHF”. I’ve given this talk several times now, highlighting some of the topics in my book, VHF, Summits and More: Having Fun With Ham Radio. When I discussed my Summits On The Air (SOTA) activities, Thom/W8TAM mentioned that Parks On The Air (POTA) was probably a better fit for Michigan. (There are SOTA summits in Michigan but most of them are in the upper peninsula or the northern part of the lower peninsula.) This got me thinking about POTA and I followed up with Thom via email a few days later to get a bit more information.

Being a fan of the US National Parks, I had done a few activations during the ARRL National Parks On The Air event in 2016. (Holy decibels, was that really 4 years ago?) The POTA program is similar but is an ongoing program, kind of like SOTA.

What’s A Park?

I am not sure of the specific criteria for parks to be included in POTA, but it seems to be pretty much National Parks (including National Forests) and State Parks. The POTA website talks about these typical categories of POTA stations: backpack, picnic table, campground and Field Day.  Backpack looks very much like a typical SOTA activation, a small portable station carried by humans (or maybe goats) to the activation site. Picnic Table is a little bit different, with more gear and less hiking. Campground and Field Day take advantage of operating close to or inside a vehicle.

I see quite a bit of overlap with other activities that I like: SOTA, hiking, camping, parks and travel.

Colorado

To get a handle on local opportunities, I looked at the 85 POTA parks listed for Colorado. (Compare this to over 1805 SOTA summits in the state.) These are National Parks, National Monuments, National Wildlife Refuges, National Recreation Areas, National Grasslands, National Scenic Trails, National Historic Trails, National Forests,  and Colorado State Parks.  In short, POTA includes the National Park System, National Forests, and State Parks. Cool!

POTA parks are spread across the state of Colorado.

We see a similar picture in Kansas, which has zero SOTA summits. (Sorry, it’s just too flat.)

Kansas has its fair share of parks to activate in the POTA program.

SOTA activation opportunities are obviously skewed toward mountainous areas. Islands On The Air (IOTA) is generally near large bodies of water. However, POTA is available everywhere. Americans like parks and we have lots of them.

First impressions

I have been heavy into SOTA, so that’s the perspective I have when checking out POTA. POTA requires 10 QSOs to obtain points for an activation, while SOTA requires only four. SOTA activations must not be in, or in the close vicinity of a motor vehicle, cannot use a permanent electrical power source, nor use a fossil fuel generator.  Also, no part of the station may be connected in any way with the motor vehicle. All equipment must be operated from portable power source (batteries, solar cells, etc). The POTA rules don’t have these restrictions.

The SOTA points system and logging database are pretty much on the honor system. Send in a log (Activator or Chaser) and you’ll get credit for the points you claim. POTA only collects logs from the Activators. So if you are a Chaser (Hunter, in POTA terminology), you don’t submit a log and your points are dependent on the Activator getting a log submitted. POTA log submission is via email and may take up to two weeks to get processed, while SOTA is instantaneous.

What’s Next

I have not quite figured out how I will participate in POTA. For starters, it can be a nice overlap with SOTA. Most of the SOTA summits we activate are on National Forest land, so they also count as POTA activations. Lately, Joyce/K0JJW and I have been RV camping in state parks, so that sets us up for an easy POTA activation. We are also working on visiting all of the US National Parks. POTA probably isn’t a great match for VHF operating, unless it has some Height Above Average Terrain.

I can appreciate the accessibility of the POTA program. It does not require a lot of physical ability to do an activation. If you want to hike into a remote area, that works, too. The flexible rules allow hams to set up a station in a variety of ways and it seems most hams have a park nearby they can activate.

73 Bob K0NR